Airsoft Installing a Mosfet on Version 6 Gearbox

The MOSFET (Metal Oxide Semiconductor Field Effect Transistor) is ofttimes misunderstood, but the best airsoft guns have them installed. The MOSFET is the encephalon of your AEG and allows yous to control the rate of fire, or ROF, by assuasive y'all to burn the gun in full auto. (This commodity steps you through how to install a MOSFET Airsoft.) This is important for two reasons: The first is that the MOSFET protects the trigger contacts from called-for up with each shot. In the event of a short or a weak battery, or an improperly charged bombardment, the gun volition automatically stop firing. The second is that the MOSFET is a mechanical switch that prevents double-fires and the situations that crusade them.

Convinced yet 🙂 ?

So, how do I install a MOSFET airsoft? A MOSFET is installed in an airsoft gun by removing the gearbox, detaching wires from and reattaching MOSFET wires to the trigger contact using a soldering iron. Next you adhere the correct wires to the motor connector and Deans connector.

To read more step past step instructions on how to install a MOSFET in your airsoft gun, continue downwardly below!

How to choose a MOSFET (four Types)

Before you buy your MOSFET you need to see which blazon of MOSFET volition arrange your needs best. Below are the different types of MOSFET yous should consider:

i. Regular MOSFET

Regular MOSFET are the simplest type of MOSFET which functions to divert the current from and protect your trigger. These volition exist the cheapest form of MOSFET and then a bang-up place for a novice to attempt your hand at altering your airsoft gun.

2. Plug and Play

Most versions of plug and play MOSFETs are just that, you plug in the MOSFET between the AEG and the battery to redirect the current from the trigger and you are set to play. This volition not crave yous to do whatsoever rewiring. Some plug and play will demand to be rewired if they come with whatever extra features.

three. Programmable

Programmable MOSFETs permit for you to requite more customization to your airsoft gun. You can change how the currents are diverted in the excursion and to allow for more functionality of your airsoft gun. Installing a programmable MOSFET will require soldering and rewiring.

4. Drop-in trigger boards

Drop-in trigger boards will be the almost expensive, but also the well-nigh desirable MOSFET. These MOSFETs can improve the feel of your airsoft gun's trigger, add together on bluetooth capabilities, supercede trigger contacts with sensors, etc. You will also need to use soldering and rewiring to install a drop-in trigger board.

What you will need to install your MOSFET

Soldering iron
Solder
MOSFET unit
Wires
Wire clippers
Wire strippers
Oestrus shrinking
Pliers
Any other tools needed to detach your airsoft gun.

Stride i- Review instructions provided in MOSFET kit

It is important that you bank check the instructions that were provided with your MOSFET and alter any of the following instructions so that they marshal with the steps given by the manufacturer.

Step 2 – Disassemble your airsoft gun

Exist certain to take annotation of what you are removing from where. It may be best to accept pictures of the process so that you know what screws go back where when reassembling your airsoft gun. If yous are unsure of the disassembly process for your specific airsoft gun, expect online for guides regarding specific parts of your model.

Step 3 – Remove the gearbox

Remove the gearbox and disconnect the wires attached to the trigger contact by soldering them off. Check online for your specific model for how to remove and identify the gearbox.

Step 4 – Trim wires

Trim the wires that come with your MOSFET kit to your desired length based on your airsoft gun. Utilise wire strippers to strip the insulation from the ends of the wire. Tin the ends of the wire with solder.

Step 5 – Solder wires to trigger contacts

Employ soldering iron to install the thin tinned wires to the unattached trigger contacts. Practise non allow positive wires to touch to avoid shorting out your MOSFET.

Step 6 – Solder wires to motor connector

Take the tinned motor connectors and adhere them to the wire connectors using the soldering iron. Using a lighter install heat shrink on the wires. This is of import to not short out your MOSFET.

Step 7 – Solder wires to Deans connector

Accept tinned motor connectors and attach them to the wire connectors using the soldering iron. Install estrus shrink on the wires using a lighter. Take the Deans connector and use the soldering fe to tin information technology. Take the wires and connect the positive wire to the positive wire on the Deans connector and negative to the negative on the Deans connector. Make sure you match positive with positive and negative with negative.

Pace 8 – Check placement of wires

One time y'all have finished soldering, ensure that the wires are plumbing equipment correctly in their placements. Brand sure the rubber bar and trigger can movement over the wires and that the signal and positive wires are pushed down equally far every bit possible where the motor shaft comes upward. Ensure the gearbox tin can as well attach without whatever wires in the way.

Pace 9 – Check for correct installation

Reattach the gearbox and cheque to make sure the trigger and safe works correctly.

Step 10 – End reassembly

One time you have confirmed that the MOSFET is functioning and installed correctly, stop reassembling your airsoft gun.